Newbie with questions seeks Experienced Ones with answers

  1. #1 by Sharon Jessen on 12-06-2012
    Sharon Jessen's Avatar
    Posts: 3

    Newbie with questions seeks Experienced Ones with answers

    Hi, I am new to this forum. I joined because I have questions about using my Behringer Xenyx 1622FX mixing board. I am a singer, not a sound engineer, and I found the user manual for my mixer to be too advanced for me! In spite of my limited experience and knowledge, I managed to get the board hooked up and do a basic mix and sent the mix out to my computer to make a recording which I transferred to CD. I want to do some more recording and I have a few problems, so now I want to understand my mixer better so I can fix some of these issues.

    I found the book "Basic Mixers" by Paul White and am starting to go through that. I would be interested in knowing what others might recommend as a good place to start to learn about understanding and operating a mixer. Is there a book or magazine or website you would recommend?

    A specific problem I am working on at the moment is how do I create a mix in the headphones that is different from the main mix. I use headphones to listen to my accompaniment music while I record myself singing, and to get the sound to balance on my computer I have to turn the music up really loud (I am using an iPod hooked up in the tape in ports). When I turn the music up on the iPod to the volume necessary for it to register on the computer, I can't hear myself singing and I tend to strain my voice to sing over the music. I'd like to be able to send a different mix to the headphones than to the main. I'm wondering if this can be done through the aux sends which I am just learning about. Am I on the right track? (no pun intended) or is there a better option?

    Thanks
  2. #2 by Sharon Jessen on 12-06-2012
    Sharon Jessen's Avatar
    Posts: 3
    Well, I spent the day reading my "Basic Mixers" book by Paul White and I believe I am slowly starting to get a grasp of what all those knobs and sliders are there for. With White's book and my mixer's User Guide in hand, I am beginning to make some progress in understanding my mixer.

    I also found a website called Sound on Sound that White contributes to that seems to have some good info if anyone is interested.

    To answer my own question above, it appears that using the aux is a way to create a "cue" mix that is different from the main mix. I'm still trying to figure that out completely. Will have to fiddle with my mixer a bit to see if what I am understanding is going to work.

    I don't believe these guys anymore who say that the mixer is not as overwhelming as it appears. I think it is! There is a lot to it!

    Well, I'm still open to any help. Just thought I would do an update on what I have discovered so far.

    Thanks!
  3. #3 by Glenn Slater on 12-17-2012
    Glenn Slater's Avatar
    Posts: 143

    Xenyx 1622fx

    - Sharon Jessen wrote View Post
    Hi, I am new to this forum. I joined because I have questions about using my Behringer Xenyx 1622FX mixing board. I am a singer, not a sound engineer, and I found the user manual for my mixer to be too advanced for me! In spite of my limited experience and knowledge, I managed to get the board hooked up and do a basic mix and sent the mix out to my computer to make a recording which I transferred to CD. I want to do some more recording and I have a few problems, so now I want to understand my mixer better so I can fix some of these issues.

    I found the book "Basic Mixers" by Paul White and am starting to go through that. I would be interested in knowing what others might recommend as a good place to start to learn about understanding and operating a mixer. Is there a book or magazine or website you would recommend?

    A specific problem I am working on at the moment is how do I create a mix in the headphones that is different from the main mix. I use headphones to listen to my accompaniment music while I record myself singing, and to get the sound to balance on my computer I have to turn the music up really loud (I am using an iPod hooked up in the tape in ports). When I turn the music up on the iPod to the volume necessary for it to register on the computer, I can't hear myself singing and I tend to strain my voice to sing over the music. I'd like to be able to send a different mix to the headphones than to the main. I'm wondering if this can be done through the aux sends which I am just learning about. Am I on the right track? (no pun intended) or is there a better option?

    Thanks
    Hi Sharon,

    This is really about two things: How you have your equipment connected and how you are routing your signals.

    It is really important to make sure that you are using the control room feature of your mixer. Your studio monitors should be connected to the CTRL ROOM OUT of your XENYX1622FX mixer.

    Now what is coming out of your studio monitors is the same as what is coming out of your headphones. Your headphones are independent of your main mix.

    On the right side of your mixer is a section labelled SOURCE. These buttons decide what you hear in your headphones. If you press the red button labelled "2TR/USB" you will hear what is coming from the I Pod.
    If you press the "MAIN MIX"button you will hear what is being recorded.

    Whenever you are recording with a live mic, make sure your studio monitors are muted and that you are using headphones.

    The best way is to record you iPod first, so that it is recorded at a proper level. Then setup your recording software to play back the iPod track while you record your vocal.

    1. In the SOURCE section, press the 2TR/ USB button, and the MAIN MIX buttons.Make sure that the 2 TR/USB TO MAIN button is UP.
    2. On your software, adjust the level of the playback of your iPod track that you are listening back to. If you can't hear the backing tracks, turn them up on your software and turn the "PHONES/CTRL ROOM" knob on your mixer DOWN a bit.

    Glenn Slater
    Specialist, Product Support Web
    MUSIC Group US
    BEHRINGER
  4. #4 by Steve Fry on 06-13-2018
    Steve Fry's Avatar
    Posts: 2

    issues with my xenyx 1622fx mixer connecting for live performance

    Hi can you help,

    I have just bought a Behringer xenyx 1622 fx mixer I have connected it through a skytec amp to two HS 300 watt passive speakers ( amp and speakers work fine) however when I have two mics and guitar connected there is hardly any volume with everything turned up full effects work as they should but volume is very low.

    I also have a eurorack MX802A mixer and when connected with same set up has far more volume.

    My question is do I need to be pressing I button or two on the xenyx I have the main out going from the top of the mixer the same as the eurorack. I just want to use the xenyx as a live performance mixer.

    Thanks in advance

    Steve
  5. #5 by Oleh Kross on 06-22-2018
    Oleh Kross's Avatar
    Posts: 2

    the light bulb stopped burning

    help, can someone tell me (I do not want to create a new topic)
    The light in the microphone stopped burning с1
    need to be carried in repair? Will it affect the performance of the microphone
    he is still writing the sound normally
  6. #6 by Mark Farrell on 06-22-2018
    Mark Farrell's Avatar
    Posts: 70
    - Where are the levels on the VU meters compared to the other mixer?
    - Do you have headphones that you can compare volume levels of the two mixers?
    -Not sure which buttons you may be referring to, but I believe for most 'normal' setups all should be 'up/out' for routing to the main outs.
  7. #7 by Oleh Kross on 06-23-2018
    Oleh Kross's Avatar
    Posts: 2
    help, I do not know what to do
    I'm afraid that the microphone will stop working
  8. #8 by Paul Vannatto on 06-23-2018
    Paul Vannatto's Avatar
    Posts: 10,278
    Hi Oley,

    That mic requires phantom power. Has that been enabled on the mixer for that channel?

    __________________________________________________ _______________________
    For additional help please refer to the X32 wiki pages for updated and current documentation about the X32.

    For official technical and warranty support for your product you should contact the support team through their CARE department. You can contact CARE by phone at (+1) 702-800-8290 for the US and Canada and (+44) 1562 732290 in Europe.

    You can also contact CARE via email at CARECREA@music-group.com. They strive to respond to emails within 24-48 hours during normal business hours, but please be patient if it takes longer due to the volume of emails they receive.


    Paul Vannatto
    Volunteer Forum Community Moderator
  9. #9 by Mark Farrell on 06-23-2018
    Mark Farrell's Avatar
    Posts: 70
    If the mic still functions properly with phantom power (36 to 48 vdc) enabled, I would not worry about the LED not being lit.
    Unless the mic is still under warranty, the cost of a repair would likely be equal or more that the cost of a new mic.
    What are you using for an interface/mixer/preamp? Some small mixers may only provide 15 to 18 vdc and may not be enough to light the LED.
    Have you tried another XLR to XLR cable?