Getting sound both sides

  1. #1 by Ron Cox on 4 Weeks Ago
    Ron Cox's Avatar
    Posts: 11

    Getting sound both sides

    Hello,

    I just downloaded a demo version of ToonTracks EZmix. I seem to only be able to get the effected sound in one side of the monitors or Cans. Is there a way to get it balanced?

    "The older I get..the better I was"
  2. #2 by Paul Vannatto on 4 Weeks Ago
    Paul Vannatto's Avatar
    Posts: 11,102
    Hi Ron,

    Welcome to the forum. ToonTracks EZmix is not a Music Group app. Are you using one of their mixers or equipment? If so which one, and how do you have it hooked up to your computer?

    __________________________________________________ _______________________
    For additional help please refer to the X32 wiki pages for updated and current documentation about the X32.

    For official technical and warranty support for your product you should contact the support team through their CARE department. You can contact CARE by phone at (+1) 702-800-8290 for the US and Canada and (+44) 1562 732290 in Europe.

    You can also contact CARE via email at CARECREA@musictribe.com. They strive to respond to emails within 24-48 hours during normal business hours, but please be patient if it takes longer due to the volume of emails they receive.


    Paul Vannatto
    Volunteer Forum Community Moderator
  3. #3 by Ron Cox on 4 Weeks Ago
    Ron Cox's Avatar
    Posts: 11
    Thanks Paul for your response.

    I realize Toontracks products are separate. EZmix is a software plugin by Toontrack It has both stand alone and plugin modes. It's similar to others I have like Guitar rig 5, and Line6 POD Farm.

    However when I try to operate the EZmix in stand alone mode it appears only in one side. Not knowing the signal flow of the Behringer unit, and it not being supplied to the user, Its hard to know. It seems to lend itself only one way, I mean only 1.3 left or 2/4 right only. Is this correct?

    "The older I get..the better I was"
  4. #4 by Ron Cox on 4 Weeks Ago
    Ron Cox's Avatar
    Posts: 11
    Just curious is this the only place to get help/support for a Behringer product?

    "The older I get..the better I was"
  5. #5 by Mark Farrell on 4 Weeks Ago
    Mark Farrell's Avatar
    Posts: 95
    Ron,
    Is there something in the 'Menu' or elsewhere of EZMix to setup audio options for selection of routing for the interface device you are using?
  6. #6 by Paul Vannatto on 4 Weeks Ago
    Paul Vannatto's Avatar
    Posts: 11,102
    - Ron Cox wrote View Post
    Just curious is this the only place to get help/support for a Behringer product?
    Ron without knowing what Behringer product (out of over 500 currently available) you are using, I can't be of much help. If you are using the X32, the answer will be different than if you are using a Xenix analog mixer. Sorry, but my crystal ball went in for repair a long time ago.

    __________________________________________________ _______________________
    For additional help please refer to the X32 wiki pages for updated and current documentation about the X32.

    For official technical and warranty support for your product you should contact the support team through their CARE department. You can contact CARE by phone at (+1) 702-800-8290 for the US and Canada and (+44) 1562 732290 in Europe.

    You can also contact CARE via email at CARECREA@musictribe.com. They strive to respond to emails within 24-48 hours during normal business hours, but please be patient if it takes longer due to the volume of emails they receive.


    Paul Vannatto
    Volunteer Forum Community Moderator
  7. #7 by Thomas Alexander on 3 Weeks Ago
    Thomas Alexander's Avatar
    Posts: 16
    - Paul Vannatto wrote View Post
    Ron without knowing what Behringer product (out of over 500 currently available) you are using...
    Hi Paul,
    Based on Ron's previous post, I think he may be talking about the UMC404HD.
  8. #8 by Ron Cox on 3 Weeks Ago
    Ron Cox's Avatar
    Posts: 11
    Thanks for your response Mark, There are only the normal to the U-Phoria 404 1,2,3,&4 in the only options 1&3 grouped for left, or 2&4 grouped for right. for both input, and output. None of these options gives me any one input of the 404 with both 1&2 together, or right & left, only 1 for input 1,,left , and 1 for input 2..right, and 1 for input 3..left, lastly input 4..right reflects output right only! No one input outputs both right or 1/3 and left, or 2/4 at the same time!? In other words no one input has right& left output.


    Sorry Paul..fair enough. Thought I'd mentioned that. U-Phoria 404 Driver ver. Running Windows 10 everything current on updates.

    Thank you Thomas right you are!
    Attached Images Attached Images

    Last edited by Ron Cox; 3 Weeks Ago at 09:38 AM.
    "The older I get..the better I was"
  9. #9 by Ron Cox on 3 Weeks Ago
    Ron Cox's Avatar
    Posts: 11
    Sorry,

    how does one post a image on this site? Tried all the usual ways I know of.

    "The older I get..the better I was"
  10. #10 by Mark Farrell on 3 Weeks Ago
    Mark Farrell's Avatar
    Posts: 95
    - Ron Cox wrote View Post
    Sorry,

    how does one post a image on this site? Tried all the usual ways I know of.
    'Uploads Attachment'
    Be sure the image is of a correct extension (jpg typically used) and file size as noted in the box that comes up. Select the file, upload and at bottom of the upload box 'Close' when done.
    Attached Images Attached Images