1. Search
    Last Post
    Replies
    Views
  2. IIRC a while ago there was an issue with iQ...

    IIRC a while ago there was an issue with iQ speakers: they'd turn themselves off if a signal wasn't present for a while, and sometimes they wouldn't turn back on when signal was present. A firmware...
  3. That'll be fine. It's not like it's going to get...

    That'll be fine. It's not like it's going to get any hotter (unless you leave it in the sun for hours on end.) As long as you're not *using* it inside a case, it's all good.
  4. 2 Days Ago
    3
    36

    Assuming X\M32, there is no M-Sum. It's a...

    Assuming X\M32, there is no M-Sum. It's a separate bus. You can use the mtxs as M-Sum if you need. The LR, M\C and mtxs all have the XO options for their peq (BS, BW, LR.) Mixbus1-16, although...
  5. That AES50 setup will work. You'll lose some...

    That AES50 setup will work.

    You'll lose some local inputs, but the aux-in remap can be used to gain up to 6 of them (in pairs) back, at the expense of using the TRS sockets on the rear of the...
  6. 3 Days Ago
    2
    71

    If you've set up the FX as an insert (as opposed...

    If you've set up the FX as an insert (as opposed to a side-chain,) then the pre\post setting doesn't matter.
  7. +1 to what Paul said. A 2nd X32 rack would give...

    +1 to what Paul said. A 2nd X32 rack would give you more IO than a single S16 would, a 2nd card interface for integrating with other systems (eg Dante) or just doing a redundant recording, and could...
  8. That won't fit in an X32. The X32 has 16x mono...

    That won't fit in an X32.

    The X32 has 16x mono buses. They can be stereo-linked to provide 8x stereo mixes.

    You can get 9x stereo mixes if you don't need LR (LR becomes the 9th mix.)
    ...
  9. No risk of physically damaging a channel, but you...

    No risk of physically damaging a channel, but you could clip something, and that would sound bad. You'd also get some nasty cracks and pops whereever that channel is routed (FOH, monitor wedges, and...
  10. 6 Days Ago
    4
    74

    Except in this case it's adjusting the *input*...

    Except in this case it's adjusting the *input* sensitivity for ch5-12. If whatever's plugged into those inputs is "consumer grade" and runs at -10dBu, then you should have those buttons pushed in,...
  11. Correct. The console is built with everything...

    Correct. The console is built with everything being coherent, regardless of what channel\bus processing is engaged *except* if you use inserts.
  12. If using the channel compressor (as opposed to...

    If using the channel compressor (as opposed to one of the boutique emulations; Fairchild, LA-2A etc as an insert,) then no, it shouldn't add any latency.

    By default the signal path is eq > post-eq...
  13. 1 Week Ago
    7
    125

    Create a stereo bus on the M32 (Select a bus,...

    Create a stereo bus on the M32 (Select a bus, press the "Stereo Link" button.)
    Push channels into it the way you would any other bus to create the stereo drum mix.
    Ensure the bus's master fader is...
  14. 1 Week Ago
    6
    128

    TLDR: leave them all off. "Lock stagebox" is...

    TLDR: leave them all off.

    "Lock stagebox" is an option for the DL\S16s, whose preamp gains can be controlled via the front panel on the stagebox. This option can stop the front panel on those...
  15. Ch31+32 feed bus1+2 pre-fader so their level...

    Ch31+32 feed bus1+2 pre-fader so their level shouldn't affect the mains... providing that the bus1+2 path is the only one they take to LR. That's not the case though. Ch31+32 are also routed...
  16. Haven't looked at it in a huge amount of detail,...

    Haven't looked at it in a huge amount of detail, but all your buses are routed to LR, if they're being used for monitors that shouldn't be happening. Also, bus1 and bus2 are both panned right. ...
  17. Select bus1\2, then in the channel strip under...

    Select bus1\2, then in the channel strip under the screen, in the "Main Bus" section, press the "Main Stereo" button so it illuminates orange. If you've got the buses stereo-linked, then this bus>LR...
  18. 1 Week Ago
    3
    75

    The TMG ASIO driver allows for 18x18, however the...

    The TMG ASIO driver allows for 18x18, however the OS\apps have to be able to use ASIO to actually see all the channels. Most DAWs are ASIO compatible, and can therefore see all 18 channels, but some...
  19. A few things about your scene: Bus1+2 aren't...

    A few things about your scene:

    Bus1+2 aren't stereo-linked. Yes, they are hard-panned, but if you stereo-link them you'll be able to pan a mono signal around the stereo field using a normal pan...
  20. Upload your scene file so we can see how the...

    Upload your scene file so we can see how the mixer is configured.
  21. Sounds like you’ve got channels feeding bus 9-10...

    Sounds like you’ve got channels feeding bus 9-10 post fader. Select a chhanel, sends tab, change the send to bus 9-10 tap point to match the setting for bus1-8 (probably post-eq.)
  22. 2 Weeks Ago
    1
    52

    AFAIK that's exactly how the XR18 works. In...

    AFAIK that's exactly how the XR18 works. In Setup>Audio\Midi you can configure it as an 18x18 or a 2x2 interface.

    In In\Out>USB sends you can tell it exactly which signals you're wanting to come...
  23. 2 Weeks Ago
    7
    150

    Of course it's your money, but the X32Rack still...

    Of course it's your money, but the X32Rack still only takes up 3RU, but gives you more buses+IO (you'd have enough to put everyone on stereo ears + LRM, you can't do that on an XR18,) more DSP with...
  24. 2 Weeks Ago
    11
    354

    You could just apply all channels (though not FX...

    You could just apply all channels (though not FX returns) to a single DCA and call it "FOH."


    Do you not miss out of the top end of the kick+bass in FOH? All you'd get is thump, no attack, and...
  25. 2 Weeks Ago
    7
    150

    XR18 + a couple of those personal monitors = $...

    XR18 + a couple of those personal monitors = $ for an X32Rack...
  26. You're welcome. The other thing you'll want to...

    You're welcome.

    The other thing you'll want to consider is a P16-D (or 2, depending on DL16 placement around the stage.) It's sort of undocumented that an ultranet signal doesn't like being...