1. Search
    Last Post
    Replies
    Views
  2. 15 Hours Ago
    6
    61

    Hi Quote from Manual manual located here:...

    Hi

    Quote from Manual


    manual located here: MANUAL
    quoted from page 76
  3. 15 Hours Ago
    1
    20

    Hi There is NO EQ on a per preset basis for...

    Hi

    There is NO EQ on a per preset basis for the the LEAD voice.

    You have a Vocal EQ in the TONE settings in the System area, but this is not per preset; its a system wide setting.

    The...
  4. 2 Days Ago
    2
    56

    Hi The VL3 dos not have AFAIK midi cc/pc or...

    Hi

    The VL3 dos not have AFAIK midi cc/pc or sysex to control any of the looper/bt functions.

    The T2 looper memory unfortunately is volatile, so all loops etc are lost after a power cycle.
  5. Hi If you turn one of the Mix Controls then...

    Hi

    If you turn one of the Mix Controls then tab over to EFFECTS MIX, you have an option in there for VOICES. This adjusts the voices level in the MAIN MIX, 0db is the default, if you set this to...
  6. Hi Louis Isaac, Make sure you save the preset...

    Hi Louis Isaac,

    Make sure you save the preset after you have made the key/scale change.
    Make sure that you have Global Key/scale set To OFF. Setup (System 9/13) Global Key (OFF)
  7. Hi That looks like a corrupted firmware; this...

    Hi

    That looks like a corrupted firmware; this is rare ( as in I have never experienced it and mone are 3-4 years old).

    The VL3 has a special firmware that is hard coded into the device and is...
  8. 2 Weeks Ago
    3
    106

    Hi Allen Jesudasan, When using a Condensor...

    Hi Allen Jesudasan,



    When using a Condensor Mic it will require 48v Phantom Power to operate correctly.

    Changing your mic type to Condensor should fix your issue.
  9. 2 Weeks Ago
    5
    455

    Hi Bill, Option 1. Have you tried putting the...

    Hi Bill,

    Option 1.
    Have you tried putting the latest firmware on using maintenance mode.
    The VL3 has a special mode that will use a firmware designed for diagnostic that should boot when the...
  10. Hi Yes its possible; thats why the check of...

    Hi

    Yes its possible; thats why the check of the serial number on labels against the serial number the device; was important in this case.

    As far as I understand the serial number for the device...
  11. Delete Backing Tracks Press STORE, navigate to...

    Delete Backing Tracks

    Press STORE, navigate to MANAGE TAB, use the left small knob to change the option to read DELETE BACKING TRACK, use the right small knob to select the track you wish to...
  12. Hi Roberto Iacolino, If you check what the...

    Hi Roberto Iacolino,

    If you check what the VoiceLive 3 Serial Number is; by Holding Down the Genre Button, a VoiceLive 3 will start with 145?????? and a VoiceLive 3 Extreme starts 177?????. If...
  13. 3 Weeks Ago
    2
    136

    Hi As Far as I remember, the Barri White...

    Hi

    As Far as I remember, the Barri White preset uses the HardTune Effect Block to generate the -12ST Shift.
    So if you were to change the SemiTone shift value more to the 0ST range, and also...
  14. Hi Andrew, Odd; I have not had that issue...

    Hi Andrew,

    Odd; I have not had that issue before.
    What input is causing the Distortion, is it Vocals, Guitar, or Another Input?

    Some Thngs to Check.
    The VL3 has independent mixes for...
  15. Hi If I am reading your post correctly, it...

    Hi

    If I am reading your post correctly, it appears as though you have how it works back to front.

    The VoiceLive 3 is Preset orientated, so you assign the Backing Track to the Preset.

    This...
  16. Hi Ben. You can set a Preset/Step individuals...

    Hi Ben.

    You can set a Preset/Step individuals effect(s) to be Global.

    Press Vocal/Guitar on each effect tab, you can turn global ON/OFF, its bottom of the effects page so you will need to...
  17. Hi If you press Vocals then navigate to the...

    Hi

    If you press Vocals then navigate to the Harmony Block, scroll down with the large encoder wheel to where you see V1 Mode, v2 Mode, v3 Mode, V4 Mode.
    If one of these is set to Scale or Fixed...
  18. Hi Connecting 2 vl3 via midi cable is...

    Hi

    Connecting 2 vl3 via midi cable is possible, the 'master' vl3 will send midi messages out for preset step changes and effect on/off changes.
    As there is no Midi for the Looper functions this...
  19. 08-09-2018
    1
    45

    Hi WHen you press the Effects Button, the...

    Hi

    WHen you press the Effects Button, the display should change showing which effects are on/off. You can then also turn what ever you want on/off by pressing the matrix buttons.

    Or is that not...
  20. Hi As far as I can find out the current...

    Hi

    As far as I can find out the current firmware is 1.0.00 build 13; published April 2011.
  21. Hi Trent, Is the Guitar Thru Connected? If it...

    Hi Trent,

    Is the Guitar Thru Connected? If it is then this would explain this.

    Do you have cables attached to either of the Left/Right GTR OUT Jacks of the VL3, if so then this will mute the...
  22. Hi There will be a slight delay as the effects...

    Hi

    There will be a slight delay as the effects are applied to LEAD Input.

    However the VoiceLive 3 has a Trick up its sleeve :)

    If you Press Setup->Input and Look for the Lead Delay Option, (...
  23. Hi If you download and Install VoiceSupport 2...

    Hi

    If you download and Install VoiceSupport 2 from the page you have linked to.

    Then connect your Device to your computer, when you then run VoiceSupport 2, it will inform you of the latest...
  24. 08-01-2018
    4
    205

    Hi John Does the following Diagram help?

    Hi John

    Does the following Diagram help?
  25. Hi Most Odd. I have logged in and...

    Hi

    Most Odd.

    I have logged in and downloaded using windows ( IE,Firefox and Chrome) and (Safari,Firefox) on High Sierra.

    I have just cleared the server cache, so maybe that may help you, try...
  26. 07-22-2018
    3
    159

    Hi Make sure you have all your MIDI settings...

    Hi

    Make sure you have all your MIDI settings Correct.

    MIDI Source = USB
    Midi In Filter = None
    Midi Out Fiter = None
    Input 7 Output Filter = 1
    Sysex Id = 0